View As Webpage | View Archives | Email a Friend

 
 
 
February 28, 2017
 
Industry news 
 





 
Technical Paper 
 
White Paper

WHITE PAPER: Crystallization in Epoxies: How to Identify and Reverse it

Crystallization in epoxies is a common occurrence –and easy to remedy. If your production facility discovers a container of epoxy that appears cloudy or is nearly solid, there’s no need for concern. In fact, in this technical paper, we hope to dispel the perception that crystallized epoxy is not usable or that its material properties are compromised. In fact, crystallization indicates purity of product. The epoxies supplied by Fiber Optic Center are made with very pure resins, which can be more susceptible to crystallization. » Download
 
Technical Content 
 

MT Ferrule Geometry Specifications: Minus-Side Coplanarity in IEC 61755-3-31:2015

In regards to MT ferrule geometry measurements, Minus Coplanarity (or Minus-Side Coplanarity) is one way to describe how “flat” or “co-planar” an array of fibers is. To ensure minimum optical performance requirements of the telecom world, it is important to ensure that all fibers in a mated pair of connectors will have good contact. It is intuitive that if all fibers of both ferrules are exactly on the same horizontal plane, then all fibers will likely mate well when connected. » Read More

Why do fiber optic connectors fail? Cross-sectioning offers a view inside connectors – and insight into why they fail

How many times have you asked yourself: Why did this connector fail? I’ve been in the fiber optic industry since the 1980’s and – despite amazing technological advances – this issue continues to plague our industry. Did you know there are 4 diagnostic methods that can help to troubleshoot why a connector failed? » Read More

How to Develop a Fiber Optic Polishing Process that Produces Consistent Results

The fiber optic polishing process comes down to 5 basic steps. Note that this article focuses on single-fiber (and not MT) PC ferrules. While much of my advice applies to APC polishing, those connectors require additional considerations……. » Read More

What is the Ideal Fiber Height for a Fiber Optic Connector?

Understand all the geometry parameters that impact Return Loss and Insertion Loss…. » Read More

Are polymer waveguides in the future for the fiber optic industry?

The development of polymer waveguides as an alternate solution…. » Read More

Which passive component tester to purchase? Start by answering 7 basic questions to get correctly configured fiber optic test equipment

Foundational questions to prepare you for a PCT with the right test set configuration for your fiber optic product…. » Read More

Sanding 3D Printed Objects: How to Get a Mirror-Polish Finish

Tips to polish 3D printed objects and Steps for sanding your 3D printing project…. » Read More

Navigating IEC standards for MT/MPO measurements using interferometry

There are two types of IEC standards for MT/MPO measurements using interferometry. The first is the “Measurement Standard” and its primary purpose is to try and ensure that different instruments yield the same measurement results. The second is “Performance or Interface Standards” which relate to specific connector styles or groups……. » Read More
 
EPOXY CORNER 
 

Helpful Epoxy Tips (and a Few Tricks)

In the fiber optic cable assembly process, working with epoxy generates a lot of questions. When I visit fabrication facilities, we discuss the finer points of mixing the material, loading syringes, minimizing waste, heat-treating crystallized epoxy, and more. For this article, I decided to share a few answers to some of the questions I hear most often, along with favorite epoxy tips and tricks…… » Read More

Ideas to adjust your epoxy process: Recommendations to reduce waste (and save money) in your fiber optic cable assembly process

For fiber optic cable assembly manufacturers, bi-packs of 2.5-gram and 4-gram are typical package sizes for epoxy. While these packages contain a very small amount of material, they support the fabrication of quite a few cable connectors and assemblies. (Note that epoxy package sizes range from 2-gram to 10-gram and higher.) Which package size best suits your process? Given the many considerations, the choice is not as clear-cut as you may think……… » Read More

Bond Line Thickness & More: Answers to Common Epoxy Questions

This article addresses commonly asked questions: Why is bond line thickness important? What is the recommended minimum bond line thickness? What is the recommended needle size to dispense epoxy? If the epoxy has filler or glass beads, will that interfere with the strength of the bond – and create the need for a thicker bond line? » Read More

Epoxy Bi-Pack News – and Usage Tips for Best Results

In this article, I’ll share our update regarding epoxy packaging. Next, I’ll present best-practice tips and techniques for epoxy burst pouch/burstable seal bi-packs. You may want to save these tips – and refer to them when training your cable assembly production team. » Read More
 
Technical Consulting with Wayne Kachmar 
 

Cablers: Are you looking to work with specialty cables or furcation tubes? If so, here are key points to consider.

A growing trend in the fiber optic industry is the increasing use of specialty fibers. Clearly, telecommunications and data communications applications are the high-volume users of fiber optics, yet other areas are burgeoning. In fact, many specialty fiber optic products have moved out of the experimental stage and into commercial markets……..


Advice for raw material suppliers planning to sell to the optical cable industry: 4 points to consider – and pitfalls to avoid

In the “dog-eat-dog” world of raw materials, competition is stiff. Margins are tight. Opportunities are rare. Is your company eying fiber optics as a new market? If you’re a raw material supplier looking to sell to the optical cable industry, keep reading. Here are 4 points to consider – and pitfalls to avoid – to win and retain this new business……..


Advice for Cable Manufacturers Looking to Enter the US Fiber Optic Market

There are many differences from cable manufacturers’ home markets or even moving from Datacom to telecom type cables and testing. When consulting with manufacturers, I can provide help in understanding not only what is required, but how to actually interpret what is required. This includes guiding them past the many potential pitfalls to develop, test, and successfully qualify their fiber optic cables for the American market….


Buying used vs. new equipment: challenges in optical cable manufacture and new extrusion line business

Many times I have had the conversation about how to get started in cable manufacture or get a new extrusion line up quickly. Invariably two questions come up: How quick can I be in production and what equipment do I need? That quickly is followed by How much will it cost and how can I get it quicker? So as a result we are soon discussing used vs. new process equipment.


So You Want To Start a Cable Company or Add a Cable Making Division?

Everyone who ever sees the amount of optical cable being deployed seems to think there is a shortage of cable. In reality there are seasonal and market fluctuations that cause shortages. While there are many who want to look at starting a cable operation, there are a few basic questions that need to be answered before you even start to talk to the cable making equipment manufacturers….